Thursday, September 8, 2011

Electrolux Washing Machine AWF1210 Error Code


Reading the last alarm condition
The diagnostics system makes it possible to identify the last alarm condition which occurred during the
operation of the appliance. To read this alarm condition, after accessing the diagnostics system (see
"Access to the diagnostics / configuration system), press the FABRICS or TEMPERATURE buttons until LED L9 lights.



The alarm condition is shown on the display, or the corresponding binary code flashes on the wash phase LEDs.
=> The first four LEDs indicate the first digit of the alarm code
=> The second four LEDs indicate the second digit of the alarm code
For example, if an E41 alarm condition (door open) is generated, the display will show E41 or (if the
appliance does not feature the display window) the second LED in the first group (equivalent to 4 in binary
code) and the fourth LED in the second group (equivalent to1 in binary code) will flash. If no alarm condition has occurred, E00 is displayed.
7.6.1 Diagnostics cycle alarms
If a malfunction should occur during the course of the diagnostics cycle, the relative alarm codes are displayed. In this case, too, the wash phase LEDs (or the display) show the error cod (flashing).
Binary codes
The table below shows how to convert the binary code displayed by the LEDs into the corresponding decimal number.



Alarm codes
0 = LED off
1 = LED flashing

Alarm code = E11
LED L26 - 29 = 0 0 0 1
LED L30 - 33 = 0 0 0 1
Description of fault = Problems with water fill in wash phase (maximum 10 minutes for each fill phase)
User code = E10
Effect = Cycle PAUSED
Possible causes = Tap closed or mains pressure insufficient; solenoid valve; hydraulic circuit of pressure switches; pressure switches; wiring; main PCB

Alarm code = E12
LED L26 - 29 = 0 0 0 1
LED L30 - 33 = 0 0 1 0
Description of fault = Problems with water fill in drying phase (maximum 10 minutes for each fill phase during in the wash load untangling phase)
User code = E10
Effect = Cycle PAUSED
Possible causes = Tap closed or mains pressure insufficient; solenoid valve; hydraulic circuit of pressure switches; pressure switches; wiring; main PCB

Alarm code = E21
LED L26 - 29 = 0 0 1 0
LED L30 - 33 = 0 0 0 1
Description of fault = Problems with water drain in wash phase (maximum 10 minutes for each drain phase)
User code = E20
Effect = Cycle PAUSED
Possible causes = Drain hose obstructed; filter blocked; drain pump; pressure switches; wiring; main PCB

Alarm code = E22
LED L26 - 29 = 0 0 1 0
LED L30 - 33 = 0 0 1 0
Description of fault = Problems with water drain during drying or drying condenser blocked
(anti-boiling pressure switch closed on "full")
User code = E20
Effect = Heating phase skipped
Possible causes = Drain hose obstructed; filter blocked; drying condenser blocked; drain pump; pressure switches; wiring; main PCB

Alarm code = E31
LED L26 - 29 = 0 0 1 1
LED L30 - 33 = 0 0 0 1
Description of fault = Electronic pressure switch circuit faulty (frequency of pressure switch signal out of limits)
User code =
Effect = Cycle blocked with door closed
Possible causes = Electronic pressure switch; wiring; main PCB

Alarm code = E32
LED L26 - 29 = 0 0 1 1
LED L30 - 33 = 0 0 1 0
Description of fault = Incorrect calibration of electronic pressure switch (electronic pressure switch level different from 0-66 mm after initial calibration drain and anti-boiling pressure switch on "empty")
User code =
Effect = Cycle PAUSED
Possible causes = Tap closed or mains pressure insufficient; solenoid valve; hydraulic circuit of pressure switches; pressure switches; wiring; main PCB

Alarm code = E33
LED L26 - 29 = 0 0 1 1
LED L30 - 33 = 0 0 1 1
Description of fault = Incongruence between level of electronic pressure switch and level of anti-boiling pressure switch 1 (duration of fault at least 60 seconds)
User code =
Effect = Cycle blocked with door closed
Possible causes = Hydraulic circuit of pressure switches; electronic pressure switch; pressure switch; wiring; main PCB

Alarm code = E34
LED L26 - 29 = 0 0 1 1
LED L30 - 33 = 0 1 0 0
Description of fault = Incongruence between level of electronic pressure switch and level of anti-boiling pressure switch 2 (duration of fault at least 60 seconds)
User code =
Effect = Cycle blocked with door closed
Possible causes = Hydraulic circuit of pressure switches; electronic pressure switch; pressure switch; wiring; main PCB

Alarm code = E35
LED L26 - 29 = 0 0 1 1
LED L30 - 33 = 0 1 0 1
Description of fault = Water level too high (level of electronic pressure switch higher than
300mm for more than 15 seconds)
User code =
Effect = Cycle blocked with door closed and water drain to 120mm
Possible causes = Solenoid valve; hydraulic circuit of pressure switches; pressure switches; wiring; main PCB

Alarm code = E36
LED L26 - 29 = 0 0 1 1
LED L30 - 33 = 0 1 1 0
Description of fault = "Sensing" circuit of anti-boiling pressure switch 1 faulty
(input signal to microprocessor always 0V or 5V)
User code =
Effect = Cycle blocked with door closed
Possible causes = Main PCB

Alarm code = E37
LED L26 - 29 = 0 0 1 1
LED L30 - 33 = 0 1 1 1
Description of fault = "Sensing" circuit of anti-boiling pressure switch 1 faulty
(input signal to microprocessor always 0V or 5V)
User code =
Effect = Cycle blocked with door closed
Possible causes = Main PCB

Alarm code = E38
LED L26 - 29 = 0 0 1 1
LED L30 - 33 = 1 0 0 0
Description of fault = Pressure chamber blocked (water level does not vary for at least 30 sec.
during drum rotation)
User code =
Effect = Heating phase skipped
Possible causes = Pressure switch hydraulic circuit; pressure switches, motor drive belt broken

Alarm code = E41
LED L26 - 29 = 0 1 0 0
LED L30 - 33 = 0 0 0 1
Description of fault = Door open (door delay interlock does not close after 15
seconds)
User code = E40
Effect = Cycle paused
Possible causes = Door open; door delay interlock; wiring; main PCB

Alarm code = E42
LED L26 - 29 = 0 1 0 0
LED L30 - 33 = 0 0 1 0
Description of fault = Problems with door closure (door open during cycle for more than 15 sec.
or door closed after cycle for more than 3 min.)
User code = E40
Effect = Cycle paused
Possible causes = Door delay interlock; wiring; main PCB

Alarm code = E43
LED L26 - 29 = 0 1 0 0
LED L30 - 33 = 0 0 1 1
Description of fault = TRIAC which powers the door interlock faulty (incongruency between status of door interlock "sensing" circuit and status of TRIAC)
User code = E40
Effect = Cycle paused
Possible causes = Wiring; main PCB

Alarm code = E44
LED L26 - 29 = 0 1 0 0
LED L30 - 33 = 0 1 0 0
Description of fault = "Sensing" circuit of door delay interlock faulty (input signal to microprocessor always 0V or 5V)
User code =
Effect = Cycle blocked
Possible causes = Main PCB

Alarm code = E45
LED L26 - 29 = 0 1 0 0
LED L30 - 33 = 0 1 0 1
Description of fault = "Sensing" circuit of door delay interlock faulty (input signal to microprocessor always 0V or 5V)
User code =
Effect = Cycle blocked with door closed
Possible causes = Main PCB

Alarm code = E51
LED L26 - 29 = 0 1 0 1
LED L30 - 33 = 0 0 0 1
Description of fault = TRIAC which powers the motor short-circuited (TRIAC short-circuit cut-out activated or motor speed more than maximum speed)
User code =
Effect = Cycle blocked with door closed (after 5 attempts)
Possible causes = Loss of insulation on motor winding/wiring; main PCB

Alarm code = E52
LED L26 - 29 = 0 1 0 1
LED L30 - 33 = 0 0 1 0
Description of fault = No signal from tachometric generator on motor (no signal after maximum time)
User code =
Effect = Cycle blocked with door closed (after 5 attempts, the last after 20 sec)
Possible causes = Motor; tachometric generator; wiring; main PCB

Alarm code = E53
LED L26 - 29 = 0 1 0 1
LED L30 - 33 = 0 0 1 1
Description of fault = "Sensing" circuit of motor TRIAC faulty (input signal to microprocessor always 0V or 5V)
User code =
Effect = Cycle blocked with door closed
Possible causes = Main PCB

Alarm code = E54
LED L26 - 29 = 0 1 0 1
LED L30 - 33 = 0 1 0 0
Description of fault = Relays contacts sticking (voltage on "sensing" circuit when the relays
should be open)
User code =
Effect = Cycle blocked with door closed (after 5 attempts)
Possible causes = Loss of insulation on motor windings/wiring; main PCB

Alarm code = E55
LED L26 - 29 = 0 1 0 1
LED L30 - 33 = 0 1 0 1
Description of fault = Motor circuit open
User code =
Effect = Cycle blocked with door closed (after 5 attempts)
Possible causes = Motor; wiring; main PCB

Alarm code = E56
LED L26 - 29 = 0 1 0 1
LED L30 - 33 = 0 1 1 0
Description of fault = Problems with motor tachimetric generator
User code =
Effect = Cycle blocked with door closed (after 5 attempts, last after 20')
Possible causes = Motor (tachimetric generator); wiring; main PCB

Alarm code = E61
LED L26 - 29 = 0 1 1 0
LED L30 - 33 = 0 0 0 1
Description of fault = Insufficient heating during washing (maximum heating time exceeded)
User code =
Effect = Heating phase skipped
Possible causes = NTC sensor incorrectly calibrated; heating element; wiring; main PCB

Alarm code = E62
LED L26 - 29 = 0 1 1 0
LED L30 - 33 = 0 0 1 0
Description of fault = Overheating during washing (temperature >88°C for more than 5 minutes)
User code =
Effect = Drain, cycle blocked
Possible causes = Heating element (earthed); NTC sensor faulty; wiring; main PCB

Alarm code = E64
LED L26 - 29 = 0 1 1 0
LED L30 - 33 = 0 1 0 0
Description of fault = Overheating during drying (drying temperature >180°C detected by NTC
temperature sensor on duct)
User code =
Effect = Heating phase for drying skipped
Possible causes = Drying NTC sensor (duct); drying heater; wiring; main PCB

Alarm code = E66
LED L26 - 29 = 0 1 1 0
LED L30 - 33 = 0 1 1 0
Description of fault = Power relay to heating element faulty (incongruency between closure of anti-boiling pressure switch 2 and status of relay K3)
User code =
Effect = Drain, cycle blocked
Possible causes = Anti-boiling pressure switch 2; wiring; main PCB

Alarm code = E71
LED L26 - 29 = 0 1 1 1
LED L30 - 33 = 0 0 0 1
Description of fault = NTC wash sensor faulty (voltage not within limits = short-circuit or open)
User code =
Effect = Heating phase skipped
Possible causes = Wash NTC sensor; wiring; main PCB

Alarm code = E72
LED L26 - 29 = 0 1 1 1
LED L30 - 33 = 0 0 1 0
Description of fault = NTC sensor on drying condenser faulty (voltage out of limits = short-circuit or open)
User code =
Effect = Heating phase for drying skipped
Possible causes = Drying NTC sensor (condenser); wiring; main PCB

Alarm code = E73
LED L26 - 29 = 0 1 1 1
LED L30 - 33 = 0 0 1 1
Description of fault = NTC sensor on drying duct faulty (voltage out of limits = short-circuit or open)
User code =
Effect = Heating phase for drying skipped
Possible causes = Drying NTC sensor (duct); wiring; main PCB

Alarm code = E84
LED L26 - 29 = 1 0 0 0
LED L30 - 33 = 0 1 0 0
Description of fault = "Sensing" circuit on circulation pump triac faulty (input signal to microprocessor always 0V or 5V)
User code =
Effect = Drain, cycle blocked (door open)
Possible causes = Main PCB

Alarm code = E85
LED L26 - 29 = 1 0 0 0
LED L30 - 33 = 0 1 0 1
Description of fault = Circulation pump faulty (incongruency between status of "sensing" circuit on circulation pump and status of TRIAC)
User code =
Effect = Drain, cycle blocked (door open)
Possible causes = Circulation pump; wiring; main PCB

Alarm code = E91
LED L26 - 29 = 1 0 0 1
LED L30 - 33 = 0 0 0 1
Description of fault = Communications error between main PCB and display board
User code = E90
Effect =
Possible causes = Wiring; main PCB; display board

Alarm code = E92
LED L26 - 29 = 1 0 0 1
LED L30 - 33 = 0 0 1 0
Description of fault = Communications incongruency between main PCB and display board
(versions not compatible)
User code = E90
Effect =
Possible causes = Main PCB; display board

Alarm code = E93
LED L26 - 29 = 1 0 0 1
LED L30 - 33 = 0 0 1 1
Description of fault = Configuration error (incongruency of configuration values when
appliance is switched on)
User code = E90
Effect = Cycle blocked
Possible causes = Configuration error; main PCB

Alarm code = E94
LED L26 - 29 = 1 0 0 1
LED L30 - 33 = 0 1 0 0
Description of fault = Incorrect configuration of washing cycle
User code = E90
Effect = Cycle blocked
Possible causes = Cycle software error; main PCB

Alarm code = EF1
LED L26 - 29 = 1 1 1 1
LED L30 - 33 = 0 0 0 1
Description of fault = Drain filter blocked (drain phase too long)
User code = Specific LED (EF0)
Effect =
Possible causes = Drain hose obstructed/kinked; drain filter dirty/blocked

Alarm code = EF2
LED L26 - 29 = 1 1 1 1
LED L30 - 33 = 0 0 1 0
Description of fault = Excessive detergent (too much foam during drains)
User code = Specific LED (EF0)
Effect =
Possible causes = Excessive detergent introduced; drain hose obstructed/kinked; drain filter dirty

Alarm code = EF3
LED L26 - 29 = 1 1 1 1
LED L30 - 33 = 0 0 1 1
Description of fault = Water leakage: intervention of Aqua Control system
User code =
Effect = Water drain to 120mm, cycle blocked
Possible causes = Leaks from base; drain pump; wiring; main PCB
Kindly Bookmark this Post using your favorite Bookmarking service:
Technorati Digg This Stumble Stumble Facebook Twitter
YOUR ADSENSE CODE GOES HERE

3 komentar:

360 grados on September 4, 2015 at 11:28 AM said...

Hi, great post.
Do you know how i can have "Access to the diagnostics / configuration system), in the EWW 1210?

Unknown on March 2, 2018 at 11:20 PM said...

Are struggling because lack of time Or Postponed to repair the Electrolux Washing Machines. Don’t worry Electronicservicecenter.in offers Electrolux Washing Machine Repair Services in Hyderabad.

Anonymous said...

We electrolux washing machine service center in hyderabad serve you with the best assistance. As we understand really how frustrating it is when an appliance stops working, hence we are ever ready to offer repair services with our highly qualified engineers, technician and plumbers. Who are made available seven days a week for helping you get your appliances working again. We give offer at low cost of price rs.350/- with 3 months swaranty.
…………………………………………………….
A reliable Refrigerator Service Centre in Hyderabad remains the best, most-trusted option for refrigerator repairs and maintenance.We refrigerator service center in hyderabad best administration community for fridge requiring little to no effort of cost rs.350/- with 3 months of guarantee on our each supplanted part in your defective appliance.
………………………………………………………..
We are here to provide Service and repairing in Secunderabadfor all types of Samsung Refrigerator, Samsung Washing Machine, Samsung Microwave, Samsung LED, Samsung LCD, Samsung TV, Samsung Water Purifier.We provide Services repair for all brands.We SAMSUNG Washing Machine Repair Hyderabad Service Center Secunderabad provide home service.We best administration community for fridge requiring little to no effort of cost rs.350/- with 3 months of guarantee on our each supplanted part in your defective appliance.

Post a Comment

 

| Code Error Washing Machine © 2014. All Rights Reserved | Template Style by My Blogger Tricks .com | Design by Brian Gardner | Back To Top |